Clik here to view.
How to apply acoustic loads to structural components? Is this possible?
I have an acoustic specification in SPL vs. Hz that I need to apply to a flat panel with its supporting frame behind it. Does simulate have the capability to complete such an analysis? I imagine it...
View ArticleClik here to view.
Creo Simulate Force & Moment graphs?
Hi, I'm trying to create some Force & Moment diagrams for a simply supported beam, with a pin support on the left side and a roller support on the right side, and some distributed and point loads....
View ArticleClik here to view.
How to know the beam element node reaction force and moment in Pro Mechanica
Hello all, I am new to Pro Mechanica. I have a question regarding to probe the reaction force and moment at a node of a beam element. In my application, I use the beam element to represent my whole...
View ArticleClik here to view.
Material Assign
Hello, If you assign a Material A to a component:And then you assign a Material B to a volume region. What happens?I mean, does the Material A overrides the Material B? Or Creo understand that I want...
View ArticleFatal error near end of run on large modal analysis...
OK I have a specific error that no one here at work has seen before. I have a large model running a modal analysis on, single pass adaptive, and after the second run sometime during or after the...
View ArticleClik here to view.
How to create multiple surface constraints for a simulation
In my mechanism below I want to simulate the bouncing shown in example provided in the exercise eleven of the How to Model Anything. The yellow man consistently goes straight through the green box...
View ArticleClik here to view.
Straight beam limitations
Hi All, This is not new but after staring long and hard at numbers that simply 'do not add up' when comparing beam and solid model results, I realise I have been here before. So I thought I would...
View ArticleClik here to view.
How to give bolt connection for slots on both plate?
Dear community, I have two plates and want to give bolted connection. Now for bolted connection, we can only select edge of diameter. How I can give bolted connection for such slots? Thanks,Jitu
View Articlehow to get the component (X,Y,Z) of the constrain reaction?
Hello there, This maybe a simple thing but I just can not figure out how to do it. Here is the thing, I have a simple part that is constrained at the hole, of course the load is applied. Now at the...
View ArticleClik here to view.
Solidworks ScanTo3D vs. Reverse Engineering Extension
Possibly not the right forum, but I'm stuck with Solidworks ScanTo3D to handle scanned point clouds. I'm having issues with poor performance / crashing software. How does Creo Reverse Engineering...
View ArticleClik here to view.
Creo Simulate Force & Moment graphs?
Hi, I'm trying to create some Force & Moment diagrams for a simply supported beam, with a pin support on the left side and a roller support on the right side, and some distributed and point loads....
View ArticleHow to analyse a vibration test table?
Hello, Is there a way to analyse the interaction and resultant displacement and stresses between a model sitting on top of a vibration test table? I have an assembly with 2 parts in, one to represent...
View ArticleClik here to view.
Finite friction blocks
Hello All, I am trying to develop a feel for the behaviour of Creo3.0's finite friction. So starting with a simple model Text book concludes no sliding.Reality tells us that the pressure...
View ArticleClik here to view.
MESH FEM MODE - HANDLE NODES
Hi all. I've a question. Is possible nodes handle in Creo Simulate when throw "Mesh/Run" inside "FEM Mode"? I need that there not jump between nodes. Attached image.
View ArticleClik here to view.
Creo simulate using the memory as "hard drive"
Hello, I have read that there is different kind of memory allocations for the Creo Simulate although the current Windows with 64-but can handle quite a big amount of memory in single machine. So my...
View Articlehow to find BELD Tension...???
Hello, I have to find the tension in belt, in belt pulley mechanism...
View ArticleClik here to view.
Is it possible to do Inertia relief analysis in Creo?
I need to analysis the stick and boom models. I have tried to do the boom but stress is high in boom mounting point because i fixed a pin as X:00 Y:00 and Z:00 displacement.
View ArticleClik here to view.
Assembly with only inherited parts and constraints
Hi! I am going to use Creo Simulate on an assembly model that contains parts that will change slightly during the design process but still not change in such ways that it will affect anything in the...
View ArticleClik here to view.
Mechanism problem
Hi Allim having a problem creating a mechanism. it consists of a worm driven gear mounted on a shaft, that turns a screw which should force a collar to travel linearly. i have the worm gear drive set...
View Article