Clik here to view.
in creo simulate, optiization design, can we obtain pressure (load) vs...
in creo simulate, optiization design, can we obtain pressure (load) vs displacement graph??
View ArticleClik here to view.
how to split symetrical model in ptc creo 3.0 for simulation?
I have a model but i want to split it in half, becase i would have then a half less finite elements. It is symetrical model. Can anyone help me?
View ArticleClik here to view.
Reading Creo results
Evening All, Has anyone come across this ... The model was originally created in Creo2 M130 (customer)I loaded into and ran it using Creo2 M100 (a quick review without having to install M130) The...
View ArticleAnalysis on Assembly with compound materials
Hi I am trying to perform structural analysis on assembly consisting of parts with different materials, What will be the failure criteria on the resultant von mises stresses?
View ArticleSpecified rotational DOF in contact Analysis
Can we release one rotational degree of freedom in contact analysis in creo simulate. When i tried giving a specified rotation to a cylindrical part but got a warning saying "you constrained rotational...
View ArticleClik here to view.
Surface region failed after model modification. Redefining not possible.
Dear All, A simulation has been run on a model, using surface regions. The sketches of the regions were made in the model (paramteric module) and they were the bases of the surface regions created in...
View ArticleHelp with Reducing Thickness in the Basement Structure (File Attached)
Hi Everybody.Hope you can help me, as you have done times before. My objective is to check, once I've reduced the thickness of the Basement (from 115 mm to 90 mm), how the stress values are (lower or...
View ArticleClik here to view.
Transient Thermal Response
This question is in regards to using the simulate analysis within the applications tab of PTC Creo Parametric 3.0. After completing a transient thermal response a plot is given of temperature vs time...
View ArticleQuestion regarding creo simulate 3.0
Hi, so I have a creo 3.0 student edition and I have a problem with the simulation taking too long to produce a result. I have set the force to be on the surface of the spring and at the bottom end of...
View Articleslow mechanism simulation
Some people here have reported that mechanism simulation run extremely slow. I had the same problem. I made a 8 wheel machine model, tires modelled as bushings and run a dynamic analysis with no...
View ArticleSimulation of gas springs
how can i simulate the mechanisms using gas springs . Can i use gas as a medium to apply pressure on the piston. how to simulate that kind of situations.Thanks in advance.
View ArticleClik here to view.
Simulate fastener questions...CSV columns and edge references.
I am having some issues with fasteners not producing expected results, I am getting fasteners showing compression when there is undoubtedly a tensile load on them. I am trying to track down what the...
View ArticleClik here to view.
Anyway I can select just the top surface for my analysis?
Hi everyone, attached in this post is a picture of my parts and the analysis that I wanna do. I have tried to set only to put a force on the top surface but this shows the whole surface instead. Anyway...
View ArticleClik here to view.
How to turn off location coordinates of view max in results window?
Hi, Anyone know how to turn off the x y z coordinates for view max measurement in the results window in creo simulate 3.0? Thanks,Don Anderson
View ArticleClik here to view.
Mechanism analysis
Hi All,I have a problem, where I want to analyse how slider block can affect the guide bar. I have looked through good few tutorials on YouTube but nothing seems to match.There is a welded frame where...
View ArticleTotal Load at Point?
I'm running a static stress analysis where the load is a Moment load about a shaft axis.For the analysis to run successfully I have to change the load distribution from "Total Load", to "Total Load at...
View ArticleAssembly with only inherited parts and constraints
Hi! I am going to use Creo Simulate on an assembly model that contains parts that will change slightly during the design process but still not change in such ways that it will affect anything in the...
View ArticleClik here to view.
Obtaining a floating Simulate license in Creo 3
I recall the ability to grab a floating license for Mechanica back in the Pro/E days. Currently I'm running Creo 3 with a PROE_Essentials license and am able to prepare a model for structural analysis...
View ArticleSiemens buys Mentor and it's CFD products
Really would have liked to see PTC buy this company.They have a very nice basic CFD product that's integrated into Creo and was looking forward to the multi physics products being integrated into Creo...
View ArticleClik here to view.
Creo Dynamic simulation for stress analysis
Hey everyone! I'm doing a simulation study on my graduation project. I have a ball screw and a nut assembly in which the nut is fixed and the ball screw is rotating and advancing linearly in the shaft,...
View Article