How do you analyze "nested" tanks under load?
I have an elliptical tank inside of another semi-elliptical tank. There is a uniform pressure load inside the interior of the inner tank and I am uncertain how to set up an analysis of this assembly....
View ArticleClik here to view.
Applying Pre-load to pressure enclosure end caps
I am trying to apply preloads to parts that make up a pressure enclosure assembly. We screw the endcaps to the main enclosure and then apply 120Nm as the preload torque. I have tried to simulate this...
View ArticleClik here to view.
how to get full simulation module for student use?
It's possible to upgrade my student edition with complete simulation module ?? When i try to work with part or assembly in Creo i have problems with simulation because i can't click on tools. Creo say...
View ArticleCluster/Distributed Computing für Creo Simulate?
Hi!Creo Simulate has a feature called distributed computing. Is this some parallel computing using e.g. MPI distributing a simulation load over multiple nodes? Is there any good setup-How-To? Is this...
View ArticleDefault legend values in result window
Hi all, Is it possible to assign default legend values in the result window? When looking at the stress results of an analysis, the highest legend value is by default set to the largest stress in the...
View ArticleNeed to simulate a roller chain in a channel
I am trying to simulate my roller chain sliding thru a "U" channel that has a radius at the end using slot connection. But I keep getting "Assembly failed to connect" wondering what I am doing wrong.
View ArticleCyclic Symmetry issues
Hi,I'm running into issues trying to run a cyclic symmetry analysis on one part of a large disk - whenever I try to mesh the model, it returns the following error: The requested shape change...
View ArticleClik here to view.
Strain Vector Results - Hide Opposite side of model vectors?
Good Afternoon, Anyone have a idea of how to hide the strain vectors in the model that are not on the surfaces that you are directly looking at?I know you can isolate by selecting individual surfaces,...
View ArticleClik here to view.
I ran 6 cases with differente loads, now, how do I know what was the load at...
Hello world, Look, I ran an analisys where I had to evaluate with different loads. After a month I had to go back and verify the stresses and deflections, the problem is that I do not how to show the...
View ArticleSurface Regions Improvements - Creo Simulate Option to Split into Segments...
Surface Regions Improvements - Creo Simulate Option to Split into Segments and SuppressPlease vote on the above idea related to Surface Regions in Creo Simulate Parametric. Thanks,Don Anderson
View ArticleClik here to view.
Refine model for torsion test
Problems with beam refine for a car chassiTrying to do my skeleton sketch to beams in simulation, is it possible?
View ArticleCan we get the yield curve in Simulate?
Hi, I have a varying load acting on a PET bottle, I want to know at which load point the bottle deforms. And once analysis is done, I want to get a graph in such a way it should show me the increasing...
View ArticleImport Load values from XLS
Is there any way to import the load details into Creo Simulate loads from XLS?I have all the load details that are output from Adams simulation in XLS format. I need to input these values into Creo...
View ArticleHow to measure change in dimension?
Hi, Lets say I have cylinder and the inner pressure load is applied thru its wall, after analysis, I want to know what is the change in diameter of the cylinder wrt applied load, so that I can make my...
View ArticleClik here to view.
BELT CONNECTION BUT OPEN FOR MECHANISM
Hi All, I would Like if is possible make a mechanism with belt open or similar construction. 3 PARTS: Fixed part, Mobile part 1 and Mobile part 2 In blue... The """ Open Belt """ Thank you guys.I...
View ArticleIs there a way to use volume regions to define prescribed temperature volumes?
Dear All,The model changes, but the volume with prescribe temperature remains in the same position. To save time by not reassigning affected surfaces after every model change, I was wondering if volume...
View ArticleClik here to view.
...and one more Thermal thing
Clearly, I haven't been using the Thermal license much lately so pleaseexcuse me if this gripe has been hashed out before.When creating a Thermal model you can apply a Prescribed Temperatureboundary...
View ArticleClik here to view.
Fasteners fail
Creo3.0 M030 My surfaces are flat, holes are co-axial, only 2 components, the most benign model imaginable and (grrr) ITAR. Original geometry from Solidworks. No lead in chamfers (first thing I dealt...
View ArticleMechanism distance measurement
Hi all, I have a query regarding mechanism. Is there any way to calculate minimum distance in moving parts?Regards,Sandeep K
View ArticleClik here to view.
Creo Simulate - stress and displacement dont fit together?
Hey there, I just simulated the displacement in Creo and the results don't fit together. So here is the data: Part geometry: 40mm x 10mm x 2mmF=5N on every longitudinal sideE=5 kPa How can I have a...
View Article