Clik here to view.
How to display reference plane or curve in mechanica analysis result?
As shown in down figures.In first figure, there are three defined curves, to act as deformation reference for the part, but in the second figure, in the mechanica analysis result, the curves will not...
View ArticleClik here to view.
Creo vs ANSYS - Stress Linearization Graphs to Compute Kt
This is not posted as a question, but I just wanted to show that Creo does just as good as ANSYS when plotting stress linearizations, and I like the formatted output better than ANSYS. If you're...
View ArticleRemove interference material as a result of mechansim
I am running a mechanism of essentially a gear shape. I would like to male tooth to cut out the female section as a result of the motion I have defined. These aren't really gears but a special profile...
View ArticleClik here to view.
Mold Analysis Lite
Mold Analysis Lite was integrated into Creo 3. PTC dropped Plastics Advisor after Wildfire 5, I think. I was happy to see it back because in the initial phases of a design I just want to look at fill...
View ArticleClik here to view.
Weighted arithmetic mean of stress in Creo simulate 2.0 ?
Hello,I need to find on a selected zone the value of the average stress weighted on the area. Create a custom surface and view the results of the analysis only on that zone is not a problem, i want to...
View ArticleClik here to view.
Displacement is way too high
Let me start by saying I am essentially self-taught when it comes to simulate. I have no training aside from a few examples on SolidWorks back in college (six years ago). I understand the mathematical...
View ArticleClik here to view.
mass idealization in modal and shock analysis
Hello,I am doing a shock analysis introducing as input a response spectre of a sismic event, function of frequency and acceleratio Se(T) [g].The idealization of a chemical reactor with the heat...
View ArticleClik here to view.
Atlas Stress Strain Curves
Hello,In responseto a requeston mattersalreadywithan integratedstresscurvein the definition, which does not seem to exist, I found a bookwith somealreadypredefined curves.Iencloseda copyof the bookif...
View ArticleClik here to view.
Simulation non linéaire avec matériau élasto-plastique
Bonjour à tous ! Je suis nouveau sur le forum, mais pas nouveau à utiliser les produits PTC car je l'utilise depuis 2007 (licence professionnelle), et plus particulièrement depuis 2008 dans mon...
View ArticleClik here to view.
In Optimization Design, how to select one part's parameters in assembly...
I am doing an assembly static analysis. In Optimization Design module, I want to take one part's parameters as variables, as show in Picture 1. But when select variables as shown in Picture 2, only...
View Articlecan of soda
Hello... Some time ago there was a study on Pro Mechanica to the buckling of a Soda Can.Itseems to mealsoonMathCad.Aperson would stillhavethesefilesorlinktoretrieve.Kind regards.Denis
View ArticleScanned data, singluar mapping
Hi, Two questions, the second resulting from the first. Thanks 1. Has anyone/can anyone share their experience of scanned component data - Real reverse engineering? Any links, contacts, papers,...
View ArticleClik here to view.
Pin and rotation in mechanica/Simulate
Hi all,I would propose to you a simplification of a problem: putting in rotation drum that push a capsule.I would see if the path of the capsule gives some problem.I've made a simplification of the...
View ArticleClik here to view.
How to fix an invalidated key frame sequence in Creo Parametric animation?
I created several snapshots to make an animation with in Creo Parametric. I created the key frame sequence, but when I try to play the animation I keep getting the following error "Key frame sequence...
View ArticleCreo Simulate - Element incompatibility
Hi all, Can anyone assist with 'Element Incompatibility' Issue? I have inherited a model featuring fairly complex extruded sections of a frame. I have checked geometries, interfaces and constraints in...
View ArticleClik here to view.
Creo Simulate vs ANSYS Workbench contact analysis w. friction.
Hello all simulation geeks... Just for fun, I made a comparison between ANSYS and Creo Simulate 3, to see what the new frictional contact can do in Creo 3. A block with a slot, a plate is located in...
View ArticleMaterial designation will not change....even though I changed it!!!
Frustration level is a 7.7 at the moment. I have two materials that I want to run a part in to compare in Simulate Lite. However, I cannot get the material to change from one to the other. Even going...
View ArticleWhat ever happend to Tad Doxsee?
His knowledge and posts were brilliant. No input from him is a significant loss. Just my thoughts
View ArticleSplit surfaces question
Hi~. I'm Creo user in S.Korea. (to be exact, PTC channel engineer)Sorry for my poor English. Now I'm studying Mechanica(WF5.0) using PTC material(Pro/ENGINEER Mechanica Simulation using Pro/ENGINEER...
View ArticleFEM Book?
Hello, For theoretical foundations, what's your recommended bibliography to fully understand Creo Simulate? Thank you.
View Article