Quantcast
Channel: PTC Community : Discussion List - Analysis and Simulation
Browsing all 1098 articles
Browse latest View live

Simulate result transparent lines in cut/section

Hi, Anyone know if it is possible to hide the transparent lines (see image) in Simulate Results after I have made a cut/section. They are annoying when I want to take pictures for report.  Stale

View Article


A tank plexiglass

HelloIneed to simulateatankplexiglassof1.0metreindiameterand2.0meterlong,closedattheendsby spherical covers.Insidethereisadepressionof400[mba].ToavoidfixingonthePlexiglasconstraintsshouldyouuse...

View Article


CREO 2.0 Buckling results

  Hey guys,I have a question about the buckling results aquired from my analysis.I am busy analyzing a component that has a global buckling mode the opposite direction of which it is being pushed as a...

View Article

Image may be NSFW.
Clik here to view.

When I start Creo Simulate, the mecbasicui license is being pulled from the...

Does anyone have an idea as to why this is happening?  The mecbasiceng license is listed on the flex license server as being available and the feature.dat file on my computer lists both licenses.  I am...

View Article

Force balance analysis for entire movement

Hi, Ive been doing some force balance analysis(with loadcell measure) for the purpose of figuring force needed to balance mechanism.(its a window opening mechanism)Basicly im looking for force that is...

View Article


Image may be NSFW.
Clik here to view.

Creo vs ANSYS - Stress Linearization Graphs to Compute Kt

This is not posted as a question, but I just wanted to show that Creo does just as good as ANSYS when plotting stress linearizations, and I like the formatted output better than ANSYS.  If you're...

View Article

How to find load at yield stress?

My goal is to do a sensitivity analysis of a part where one dimension (x) is varied. What I want out, is the force that would cause the part to reach the yield point for each change in 'x'. In other...

View Article

Image may be NSFW.
Clik here to view.

Creo Simulate vs ANSYS Workbench contact analysis w. friction.

Hello all simulation geeks...  Just for fun, I made a comparison between ANSYS and Creo Simulate 3, to see what the new frictional contact can do in Creo 3. A block with a slot, a plate is located in...

View Article


Image may be NSFW.
Clik here to view.

Automate Analysis (FEA and CFD) in Product Development

Hello everyone, We are about to make some key decision on software selection and one point of interest I have is the degree of standardisation I can implement in our product development process. That...

View Article


Image may be NSFW.
Clik here to view.

Plasticity and fasteners

NOT SUPPORTED ! Was this the case before the fasteners became beams, I haven't time to test? Ansys it is then

View Article

Creo Simulate and Windows 10

Community, Has anyone tried to load and run Creo Simulate on Windows 10?

View Article

Image may be NSFW.
Clik here to view.

Plastic deformation

HelloShouldbedeformedatubesteelof600mmdiameterand1.0mmthicktomakeaflange,as...

View Article

Image may be NSFW.
Clik here to view.

Simulation non linéaire avec matériau élasto-plastique

Bonjour à tous ! Je suis nouveau sur le forum, mais pas nouveau à utiliser les produits PTC car je l'utilise depuis 2007 (licence professionnelle), et plus particulièrement depuis 2008 dans mon...

View Article


CFD Analysis

I am curious to hear from others what you use for CFD Analysis? What integrates well or is easy to use with your Creo models? There are lots of options between Ansys, Autodesk Simulation, Mentor...

View Article

How to fix an invalidated key frame sequence in Creo Parametric animation?

I created several snapshots to make an animation with in Creo Parametric.  I created the key frame sequence, but when I try to play the animation I keep getting the following error "Key frame sequence...

View Article


Image may be NSFW.
Clik here to view.

Transient Thermal Conduction - Creo Simulate

Hello, I am trying to run a transient thermal analysis and am having trouble setting up the boundary conditions. Here is the set up: I am running the transient analysis on block 2. I have a prescribed...

View Article

Image may be NSFW.
Clik here to view.

Solver automatic load factor reduction

Hi All, When carrying out a large deformation study with contacts, load factor steps are crucial to success. The warning that one can get in the .pas file :  ** Warning:             Large displacements...

View Article


Image may be NSFW.
Clik here to view.

Simulation Results - copy clean image to clipboard enhancement request

The way I communicate the simulation results is most often to make a screen clipping and paste into a PowerPoint or email. Starting with 3.0 the results viewer is more difficult to capture a clean...

View Article

Simulate Results Definition (.rwd) Files

With the introduction of Creo Simulate, I've not been able to locate the functionality where you can insert .rwd files without having to use a template. You can do this with WF5, WF4, etc. Does anyone...

View Article

Image may be NSFW.
Clik here to view.

how does one link orthotropic material properties to a custom coordinate system

I would like to apply orthotropic material properties to a single part in my assembly model and have created a coordinate system for this component.   When I try to edit my material to apply...

View Article
Browsing all 1098 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>