Crushing a cylinder using creo dynamic simulation
Good morning all, I'm looking for some advice regarding running a dynamic simulation to crush a tube longitudinally. I have a couple of tubes which I'd like to crush so I can compare the effects of...
View ArticleClik here to view.
Rotation for part(s)
Hello, There is the "rotation" option under the "translation" but it doesn't operate so easily than the definition of translation. Why? How can I define a simple rotation (with certain angle value) for...
View Articleshowing maximum stress of multiple load sets in one result window
Hello, I am wondering if you can show the maximum stress for each element caused by different loads sets. I do not want to superpose the different stress results. My intention is to check the stress in...
View ArticleProblem using fasteners through multiple solids.
Hi, I'm using Creo Simulate 3.0 and I'm having trouble using fasteners through more than 2 solids. Creo keeps saying my model isn't constrained enough even after putting grounded springs of infinitely...
View ArticleClik here to view.
Error - geometry preparation
Hello, I often have to use the "Extrude for volume region" option.It operates well in a lot of cases but there are some situations when it leads to error: I am using this function similar in every case...
View Articlehow to create tension beams (steel cable) in simulate
Hallo Creo Simulate community I am working on a frame construction and would like to do some mechanical simulations with this frame. The simple construction is a 3D Frame with cable elements (can only...
View Articlecreo analysis inspect geometry
creo analysis inspect geometry how can i use the knots reflection and slop for surfacing
View ArticleClik here to view.
Creo Simulate Multicore Calculation
Dear All, I want to start a discussion about how Creo Simulate is using multicore and how to apply the best settings. At the Moment I am doing a lot of Simulations but the calculation time is quite a...
View ArticleSIMULATION
If two assemblies are bolted,then how to give constraints on that case..is there any regular method to give constraints or any other way on that cases..?
View Articlesimulation
if two assemblies are bolted together,then how to give constraints on that case ?
View ArticleCREO SIMULATION
How to apply the load acting downwards on the pulley or pin region in this model ?and what is the method to simulate the bolting places on the attached model ?
View Articlecreo simulation
How to apply the load acting downwards on the pulley or pin region in this model ?and what is the method to simulate the bolting places on the attached model ?
View ArticleClik here to view.
Plate bending
Hello, I have a returning problem. I often have to simulate the process of different metal plate bending. There are a lot of cases when these processes include more steps. (Bending 1, Bending...
View ArticleTrace of curves of results
HelloWhenyouwant toplotthegraphofdeformationorcompulsion,byexample of a square beam, it is easy to designate a stop on whichwill betracedthecurve.Butwhenthebeamiscylindricalandthereisnotto...
View ArticleClik here to view.
Clik here to view.
Highlighted shell has zero thickness error.
Hello, Can anyone explain the error "highlighted shell has zero or negative thickness"? I understand what it means but I don't understand what it tells me because: A. When I click on the error message...
View ArticleClik here to view.
Shock analysis using Creo Simulate ?
Hi all, I'm facing a problematic phase about an assembly. The goal of my study is determine the eigenfrequencies of an existing assembly and, if necessary, to rigidify it so it meets our criterias.The...
View ArticleClik here to view.
Animate/simulate injection mold
Hello, I would like to animate the movement of opening and closing a injection mould. Please see the attached pictures for presentation. I always make the slider connection beetween gray and green...
View ArticleCrushing a cylinder using creo dynamic simulation
Good morning all, I'm looking for some advice regarding running a dynamic simulation to crush a tube longitudinally. I have a couple of tubes which I'd like to crush so I can compare the effects of...
View Article