Clik here to view.
Cut in two piece
HelloIdoatestsimplywithawasher,seethesketchenclosed.Idothesimulationwiththewholepuckand thenwithhalfofthepuckas well ashalfoftheload.AndIgetnotthesameresulttoVonMises:Entirepuck750.0[MPa]Puck half...
View ArticleClik here to view.
Quick question re. surface regions
Am I (and my colleague) right in thinking that surface (and volume) regions are part-level features, and therefore cannot be created on surfaces resulting from an assembly-level cut? If so I may submit...
View ArticleWhy did the iterations change?
Hi, I set up an elasto-plastic study of a strut that is gradually squashed using an enforced displacement. I did not know when things would get interesting and so applied a very long time history and...
View ArticleMonitoring iterative solutions
Hello again, Related to the earlier elasto-plastic question but also LDA, contact ... It is useful to be able to monitor the progress of an iterative study by reviewing the Pass 1 results as they...
View ArticleHope to add co-simulation interface with AMEsim in dynamic mechanism module
Hello:I am working hydraulic pumps' dynamic mechanical simulation by your mechanism module. it is very good and successful to built dynamic mechanical model by your module. but it can not impose the...
View Articlecreo simulate 4.0中收敛图的纵坐标是什么意思
我在分析的结果文件夹中找到了一个文件：study.ldc（study为文件名），这个文件的内容跟收敛图的数据很接近。我对收敛图中的纵坐标不解，希望在这儿得到答案。
View ArticleClik here to view.
A bug about reviewing the total load?
When you put a force load on the flat surface, you review total load,and the result is right; But when you put a force on the sphere surface,the result is wrong, do you all encounter this kind of...
View ArticleClik here to view.
Creo Simulate vs ANSYS Workbench contact analysis w. friction.
Hello all simulation geeks... Just for fun, I made a comparison between ANSYS and Creo Simulate 3, to see what the new frictional contact can do in Creo 3. A block with a slot, a plate is located in...
View ArticleClik here to view.
Import loads in Creo Simulate 3.0
Hello. I am facing a desperate situation right now.We received from our customer a 3D model and an excel file containing a point cloud from their CFD analysis. The excel file is structured. There are...
View ArticleClik here to view.
Beam theory usid in Simulate
hi all, I'm trying to figure out what beam theory is used in Simulate with beam elements.Is it Timoshenko's theory is which a section can rotate or is it Eulers-Bernouillis theory in which a cross...
View ArticleClik here to view.
Creo Simulate 4.0 (What's new)?
Happy new year! Anyone have a link to any information regarding what's new/changed in Creo Simulate 4.0? Thanks,Andy
View ArticleClik here to view.
Angle between shell normal and solid normal must be greater than 45 degrees
I get this warning message any time I'm working with weldments larger than 2 parts: "the angle between the normal to the shell and the normal to the solid face at a shell-solid link must be greater...
View ArticleOptimization Running time
Why it takes too much time to run an optimization study while the design variable is only one and the problem is simple.I have run a static anlysis of a gear and i now i want to minimize its mass by...
View ArticleFatal error while trying to run creo simulate
While trying to run a static analysis, an error prompt pooped up soon after I hit start. I have run multiple static analysis runs on models for the past 3 months, I am not sure why this has just...
View ArticleClik here to view.
Springs distributing the load along lines (or surfaces)
I need to apply a load on a line (force per unit length) which should locally depend on the displacement of the line in a given direction; as for an elastic foundation.Is there any way to realize this...
View ArticleClik here to view.
Two pin connections in series w
Hello! I am trying to assemble a mechanical device that contains one body (an axle, body A) that is free to rotate in relation to ground and then on this body there is a new body (a ring, body B) that...
View ArticleFix problem introduced in Creo 3 Creo Simulate fasteners and materials fail...
Hi, I have found as of Creo 3 M080 that using simplified reps can cause issues with running Structural analysis in Simulate.Simplified reps cause materials, fasteners, or other simulate features...
View ArticleClik here to view.
Constraining Sliding Block
Hi all, I'm wanting to run an FEA on the attached assembly. It consists of a wedge block which a load is applied, it slides in a track until it comes in contact with a block in which the load is...
View ArticleCreo Parametric Material Files (Library)
Hi, Is there a good, current source for downloading Creo Material files? I am looking for commonly used metals and plastics. It seems crazy that every individual or organization has to create their own...
View ArticleClik here to view.
Vibration Analysis in PTC Simulate 3.0
I was wondering if anyone had any pointers on how to begin a simple vibration analysis in PTC Simulate 3.0. What I've done so far: Modelled: A plate, attached to a mass using 4 bolts (in red) as shown...
View Article