Clik here to view.
Using measured dimension from analysis in relation
Hello, I would like to learn how do we use analysed feature say distance in to relation. eg. i measure a distance using analysis which turn out to be 'x'. And if i wish to place a plane at 'x/2'....
View ArticleAnti-vibe' mounts
Hi, In a dynamic analysis, structural damping seems still to be a global number. Creo2.0, M030 Are there any methodologies to assign different levels of damping to (in my case) the mounts and supported...
View ArticlePlanetary gear design
Hi all i would like to know how to create a planetry gear reducer.I have modeled all the parts but their mechanism gives problem. Scenario is that i have a planetry gear head with 5 rows of planetry...
View ArticleClik here to view.
Elastoplastic Curve Generation
Can anyone tell me the right way to enter the elastoplasic properties of a material in Creo/WF 5.0? I have the true stress/strain curve entered. With the "Use best fit coefficients checkmarked the...
View ArticleWeighted links - co-linear points
Hi, Why can't we have co-linear points on the independent side of a weighted link? It's easy to get the warning message 'The independent geometric entities must not form co-linear points' by selecting...
View Articlemaking a belt into a part
I'm trying to draw a tank tread to fit around my wheels. I have gotten the wheels to rotate in there socket. I have also made a belt, but I cannot get the part to work. I woukd like to get the tread to...
View ArticleLinks between large displacements
Hello,I tryto representthe deformationchainthreediscs.Dimensions are inmillimeters.Load[N /m ^ 2] is uniformlydistributed."Green"discsupportsloadby deformingthe "purple" disk.In...
View ArticleParts on top of fasteners
Can anyone tell me how to solve a problem I have with assemblies I am trying to model. I have a frame work which is fastened together with fasteners and this works prefectly well until I add extra...
View ArticleClik here to view.
Gear Proper Meshing
Hi allI have a question regarding proper spur gear meshing.The two spur gear shown in the picture attached are meshed with the gear connection in mechanism by defining their pitch circle dia.but when...
View ArticleRan analysis but can't see results
I ran a static analysis on a small part and the status window says the run completed successfully, but when I click on the View Result icon or use any of the "Results" drop downs nothing happens. It...
View ArticleClik here to view.
Ball Joint in Mechanica
Is there any turn around for Ball Joint in Mechanica?I searched the forum, but couldn't find, All I see were related to Mechanism I need to do a validation on the steering arm, which transfers the load...
View ArticleHave lost confidence in mass properties calculations
Just can't rely on results. Going to have to simply use spreadsheets (which is terrible... but reliable). I've had various problems over the years so yesterday I sat down and rely analyzed things. Have...
View ArticleToo frequent corruption of optimization analyses AND model!
Been using Simulate hard for 2 years now. Have gotten a lot of very complex and useful analyses from Simulate BUT I have also paid a dear price since upgrading to Creo 1.0. My models corrupt and become...
View ArticleEditing and creating new .mtl files
A key point in executing tests in creo simulate is the identification of materials, using a .mtl file. However, the creo simulate materials library is limited in precise aluminum alloys. I was...
View ArticleClik here to view.
Dynamic Analysis Definition Motor
Hi all.See these pictures and help me to find where might be the problem.I have written the question on the second figure in red.Note: I have an MDO lisence installed.
View Articledynamic analysis on creo simulate
Hello everybody, I'd like to do a dynamic analysis of a mass spring system, I have alreay done a modal analysis so I know the resonance mode of the system. And now I am lost !! I don't know how to do...
View ArticleWeighted links - co-linear points
Hi, Why can't we have co-linear points on the independent side of a weighted link? It's easy to get the warning message 'The independent geometric entities must not form co-linear points' by selecting...
View ArticleRevolved mesh?
Hi, How do we revolve a shell mesh to get solids in Simulate? Have I missed a menu somewhere? I want a regular revolved brick mesh (with wedges where the mesh touches the axis of revolution or the...
View ArticleClik here to view.
Beam element not behaving as expected.
I have an assembly where I am modeling an anchor from a structure into concrete with a beam element and conducting a modal analysis. The end of the beam in the concrete is constraint in all 6 DOF and...
View ArticleFunction definition for dynamic shock analysis
Does anyone know hwat th erules/format is for function definition in Dynamic Shock analysis. When I enter the the function example from Creo parametric's own help file "...
View Article