Clik here to view.
Simulate friction in Creo 2
Hello, I wonder if it´s possible som simulate friction in Creo 2. Ihavea shelfmounted on8 separatecolumns. Aforce is applied tothe shelf in the direction of thearrow.Is itpossible to find out if the...
View ArticleClik here to view.
In Optimization Design, how to select one part's parameters in assembly...
I am doing an assembly static analysis. In Optimization Design module, I want to take one part's parameters as variables, as show in Picture 1. But when select variables as shown in Picture 2, only...
View Articlestatic stresses analysis on welded assembly can it be done?
Hi1. On general, can static stress analysis can be done on assembly ?2. i have a sheet metal assembly made of 2 (8mm thick) sheet metal parts, ther are assembeled by grooves and weldingi have added a...
View ArticleClik here to view.
Best Practices Document
Folks, I have been tasked with creating a "best" practices document that shows an engineer how best to start and finish a simulation project. It will contain: - How to layout you simulation- Things to...
View ArticleClik here to view.
Mechanica results variability
I've just run a Mechanica sensitivity study (linear static, using Single Pass Adaptive, remesh and repeat P-loop each iteration) and got the following result: (If this isn't legible, the lower end of...
View ArticleClik here to view.
FEA...How to define roller bearing constraint in mechanica ?
Hi,I am trying to define bearing constraint. I have base plate that is supported by two shafts at either ends. These shafts are supported by bearings so that plate can rotate around shaft axis.Please...
View ArticleClik here to view.
Does Creo Simulate distributed computing support Microsoft 2012 HPC cluseter?
Does Creo Simulate distributed computing support Microsoft 2012 HPC cluseter?Has anyone tried it?
View ArticleHow to seperate beam surface for force application?
If I want to apply force on limited region of the beam top surface how to do it .I only want to apply the force in the box region shown in picture.
View ArticleHow to eliminate singularities from the model?
I AM DOING A STATIC ANALYSIS OF A TRAILER CHASSIS AND WHEN OPTING FOR MULTI PASS SOLUTION THE RESULTS FOR VON MISSES AND PRINCIPAL STRESSES ARE NOT CONVERGING. THE STATUS FILE DURING THE RUN SHOWS...
View ArticleHOW TO RUN AN OPTIMIZATION STUDY ON A PART OF AN ASSEMBLY?
I AM ANALYSING AN ASSEMBLY IF I WANT TO EXTRACT THE LOADS ON ONE PART OF IT AND PERFORM A DESIGN OPTIMIZATION ON THAT PART. IS IT POSSIBLE.IF YES THEN HOW.
View ArticleClik here to view.
Deformed scaling factor remains in memory in the next non-scaled deformed...
Hello, I have just realized what seems to apparently be a bug in the Creo Simulate structural results visualization.It regards the deformed state option one might want to tick in the Results Window...
View ArticleClik here to view.
How to set contact interface so that two parts will not collide against each...
Hi, I am trying to simulate a case like below:Problem : The part collided (pierced through) the rigid body instead of reacting (pushed back) by rigid body.I would like to analyse the stress due to...
View ArticleClik here to view.
Beam shear and moment measures
Hi, Can we create measures for P, Vy, Vz,, Mx, My, Mz? It has always been possible to plot shear and moment graphs as follows, so the information is there. Vis results dialogue:I want to determine the...
View ArticleClik here to view.
Output many graphs at once
Hi, Is there anyway of outputting all variables from a sensitivity study? Only the active results window can be sent to .grt or .xls. If one has 20 variables and 20 sensitivity studies it can be a bit...
View ArticleClik here to view.
Missing the maximum, global sens and optimiser
Hi, Bear with me, a fairly long question and based on the global sensitivity plot below Can anyone suggest how to find C and D? Is there a function that can be used as a computed measure in a global...
View ArticleClik here to view.
FEA...How to define roller bearing constraint in mechanica ?
Hi,I am trying to define bearing constraint. I have base plate that is supported by two shafts at either ends. These shafts are supported by bearings so that plate can rotate around shaft axis.Please...
View ArticleClik here to view.
How to do "carve-out modeling" or "sub-modeling" with beams?
Hi everyone.We to solve a problem with large frame-type models. The idea is to claculate a whole frame using idealized beams first, obtain resultant forces in certain parts and apply equivalent forces...
View ArticleClik here to view.
In Optimization Design, how to select one part's parameters in assembly...
I am doing an assembly static analysis. In Optimization Design module, I want to take one part's parameters as variables, as show in Picture 1. But when select variables as shown in Picture 2, only...
View ArticleDefault units
Hello, When I want to review the stress results of an analysis, the stress units are default on "kPa". Is it possible to change the default to "MPa" instead of having to select it each time from the...
View ArticleClik here to view.
Can you hide components of an assembly in a Creo Simulte Results Window
I have an assembly FEA model and my high stress point is behind another component. I would like to do a dynamic query so that I can set up a measure at the high stress point. Unfortunately, I cannot...
View Article