Clik here to view.
cam follower mechanism
hi, I meet some problem in cam follower mechanism. You will in Picture see, how I define this cam follower mechanism. And Problem is, if I drag the component slowly, it works. But if I drag it fast,...
View Article“Restart” Option?
Hello, Does Creo Simulate have a “Restart” option? For example, let’s say that I am running a static nonlinear analysis that takes place over the course of 2 seconds. There are two Constraint Sets,...
View ArticleIsolate for exclusion control of surfaces
Hello! I have a question!How can I create an excluded area in a model?For example, in this case I want to isolate from analysis the edge of nozzle-shell junction, and is simple.But I wont also isolate...
View ArticleClik here to view.
Creo Simulate 2.0 - Modal & Dynamic Frequency Analyses
Will Creo Simulate perform the following analyses on a rotor turbine? 1. In order to perform a dynamic frequency, a modal analysis must be performed first. 2. After the modal analysis, spin the model...
View ArticleClik here to view.
how do I output element stresses/strains in tabular format in creo simulate 2.0?
I need to get element stresses & strains in table format instead of a contour plot. How do I do this?
View ArticleClik here to view.
Creo Simulate and PDMLink
Hello all,is there anyone who has "integrated" Creo Simulate file into Windchill.I understand that the result file which could be a few GB big will not be uploaded into Windchill but there are other...
View ArticleClik here to view.
Split surface in Creo for analysis in Ansys?
I'm a novice in Ansys and I'm trying to split a surface to apply a load on a portion of that surface. How do I do this in Creo?
View ArticleClik here to view.
Motion Induced Stress Analysis
Hi, I often have to review steel weldments for structural integrity which are located on a moving vessel (Pitch, Roll, Heave etc). Previously I have calculated the forces induced due to the vessel...
View ArticleK matrix
Hi all,do you know how to read the stiffness matrix?I've read of a method for understand whether the K matrix is ill-conditioned.It consist in the calculus of the condition number of K expressed as the...
View ArticleClik here to view.
Meshing sectioning and details
Hi!Just I wish to Review the elements type and size detail that CREO 2.0 Academic Edition has created and applied AutoGEM controls in the process of meshing. I could see the whole model but I have...
View ArticleClik here to view.
Simulate Results window stops opening
I've recently encountered an irritating intermittent / delayed problem using Simulate. At some stage during a session, after several iterations, the Results window suddenly refuses to open. The...
View Articlesimulation of thermal expansion
I am working on thermal expansion simulation by using Creo Simulate, the temperature distribution of the assembly was calculated by FloEFD and then exported into Creo as thermal load, and constraint...
View Articlecreo simulate save error
hi I am getting a model save error while i am saving the simulate model. any solutions
View ArticleDynamic Frequency Analysis
Hi All, I have RPM Vs Load [kW] data of motor.I want to perform dynamic frequency analysis using Creo advanced simulate extension.How to tabulate the data in Creo advanced simulate environment?Please...
View ArticleClik here to view.
Large defromation calculation
Hello, I have an assembly made of 3 components. I have defined contact between the components.When I run the analysis it prompts a warning of "Large deformation". But, in analysis setup options...
View ArticleClik here to view.
Very high quality
Hello All, Why do I have so many qualityagent.exe's running? It may be related to global sensitivity studies. I periodically end the processes because they eat all my cpu. Any thoughts? Creo3.0 M030...
View ArticleHow can I sectioning a mesh in a part/assembly?
Hi! Continuing with my previous posted question, solved to see the mesh of a part that is hide by other parts, the next issue is to cut that obtained mesh and see the elements that CREO (2.0 academic...
View ArticleMechanism & Redundancies
Hello, I have two questions. Is there a way to determine where is the redundancy while performing a mechanism analysis? For example, let's say that you assemble a mechanism and check all the steps...
View ArticleClik here to view.
Fatigue and non-lineal analysis
Hi! I´m running a model with contacts so the analysis must be non-lineal for best results. Then I must analyze the fatigue but CREO say I must select a previous lineal static analysis to do. So if I...
View ArticleLeaf Spring Dataset
Hi All, Can any one of you kindly provide a leaf spring data set if you have any. Regards,Avinash
View Article