Clik here to view.
"No analysis is associated with the limit on measure..."
So, at long last I've actually got an optimisation study working, and rather well. Having so far been optimising for displacement with a mass limit, I'm now trying to introduce some stress limits too....
View ArticleWhere can I find the Natural Frequency of a system in Mechanisms?
I'm assuming it must calculate it?Just the first one would be fine. Thanks,Cameron
View ArticleCreating a part with multiple material layers
I am looking to create a part in Creo that represents a metallised plastic part. The base material is made from a plastic material and it has a very thin (10um) copper layer on top of the plastic with...
View ArticleClik here to view.
Measures show incorrect values
Hello -- I am working with a rather complicated assembly in CREO 2 Mechanism Dynamics. Because of IP issues, I am unable to show you the model. I have rotating components, with oscillating components...
View Articlerack and pinion gear pair mechanism
I am trying to apply mechanism to rack and pinion model but it fails.can someone please share me training video for this.
View ArticleClik here to view.
PTC Creo Elements/Direct Finite Element Analysis Survey
Would anyone please let me know if PTC Creo Elements/Direct Finite Element Analysis has the following capabilities for thermal analyses? Any suggestions/recommendations are welcome too. Thanks a bunch!...
View ArticleClik here to view.
Creo Simulate Error
I am trying to run an analysis on a part with 3 different material layers but unfortunately I am receiving the following error message: Cannot process highlighted contacting surfaces. Any ideas how to...
View ArticleClik here to view.
Sodacan collapse
Isn't it wonderful what you can do with creo 3.0?it.s not Abaqus yet, but I did manage to collapse a sodacan sort of.Hope you can see the movie I made Question here: Can anyone tell me if it's possible...
View ArticlePlanetary gear design
Hi all i would like to know how to create a planetry gear reducer.I have modeled all the parts but their mechanism gives problem. Scenario is that i have a planetry gear head with 5 rows of planetry...
View ArticleSimulate Results Definition (.rwd) Files
With the introduction of Creo Simulate, I've not been able to locate the functionality where you can insert .rwd files without having to use a template. You can do this with WF5, WF4, etc. Does...
View ArticlePiston Simulation
Hey guys. I am new to Creo 3.0 Simulation. I am wanting to run a simple static simulation on a piston. I am wanting to know what would be the best set up for the push pull motion of the piston. I...
View ArticleClik here to view.
Creo 2.0 Measure Mechanism
Hi, I am a student who needs some helps! I am working on a project of design/simulation on Creo. I am trying to simulate my system, which is the following:Two blacks cylinders pull on the yellow part,...
View ArticleClik here to view.
Pin, Rigid Link - Help
Folks, I created some constraints and I am struggling to get the correct results, or should I say what I think should be the correct result. As you can see above, I created a rigid link between the...
View ArticleClik here to view.
Exit the full report of the results of Simulate
Hello,How shouldheproceedto release afull reportwithtext and imagesin Creo3.0Sumulateas wecould doin previousversions.Best Regards.Denis
View ArticleClik here to view.
Representation of curves in Simulate
Hello,Is it possibleto do this kindofrepresentationtoSimulatethe bending momentsand constraints.Best Regards.Denis
View ArticleRegeneration problem in Creo Simulate 2.0
Hi, I have a problem in regenearting a model in Simulate 2.0 (structural): in the main window, when I regenerate, the led on the bottom right remains always yellow and if I try to save the model, the...
View ArticleClik here to view.
Bike frame, FEA, Creo 2.0
Hello, Im strugling with a bicycle frame FEA for a while now (please check the pictures below).After getting over some basic problems like absolute/relative accuracy values to mesh the whole thing, I...
View ArticleAncient Pro Mechanica Motion on Windows 7
We have an old licence of PTC Pro Mechanica standalone (Wildfire 2, datecode M280). Structure runs happily on Windows 7, as does the Motion UI, but I cannot get the Motion UI to connect to the Engine...
View ArticleClik here to view.
PTC Creo simulate student version
Hello, I want to do a FEM analysis for a school project. So i downloaded PTC Creo student version which contains PTC creo simulate. But when i open a part it says i still need to get the requiered creo...
View ArticleClik here to view.