Trying to run Simulate in Creo 2.0: "cannot find ANSYS solver" message
Howdy PTC'ers, Long-time user here, just starting to use Creo 2.0. I'm trying to run a simple FEA case, and I keep getting an error message in the Diagnostic box: "Cannot find ANSYS solver, check...
View ArticleHelp with modeling hammer impact to simulate pyro-shock
Our senior capstone project involves building a test rig with a drop hammer to exite a fixture that will mount electronic components to simulate a pyro shock to them. We have creo avaliable at our...
View ArticleContact algorithm
Dear Sir/Madam, There is a couple of questions and I appreciate if someone give any advice. We are now trying to handle a contact problem between spheres. First question is what kinds of algorithm is...
View ArticleMold Analysis Lite
Mold Analysis Lite was integrated into Creo 3. PTC dropped Plastics Advisor after Wildfire 5, I think. I was happy to see it back because in the initial phases of a design I just want to look at fill...
View ArticleRun Analysis on a dedicated server
Hello.We are discussing if a server should be acquired to run Creo Simulate calculations. Is it possible for me to set up the analysis on my workstation, and when I press run, the calculations is done...
View Article"You may not enter Creo Simulate with this model."
Hello All, I'm trying to test a certain part, but everytime I try to start Creo Simulate, a pop-up will occur that says, "This model failed to regenerate. You may not enter Creo Simulate with this...
View ArticleCreo3: Stress doesn't change regardless of load.
Hi, I'm trying to run a Creo 3.0 simulation of load on a disk. When I run the simulation, the stress remains constant regardless if my load is 100 psi or 0 psi. I've attached two images of the part....
View ArticleClik here to view.
Creo Simulate 3.0: Cyclical Stress Analysis?
A project I'm working on will have a 1/16" thick, 25"x25" stainless steel sheet that will be mounted to hinges along two parallel edges. The middle will be supported by a bar attached to a linear...
View ArticleLinkage Synthesis Using Gometric Constraint Programming
Feb 6 2015 Hello. I am a mechanical inventor, and have recently become interested in parametric CAD due to two articles, both by E. C. Kinzel, J.P Schmiedeler, and G. R. Pennock, titled Kinematic...
View ArticleClik here to view.
How do I measure the torque output of a gear in Mechanisms?
Hi First off I have used gear connection as opposed to a cam follower. I have my output angular velocity but I also need the output Torque and I don't know how to analyse this? Thanks for the help,...
View ArticleClik here to view.
User need help with Simulation setup.
Hi all,I have a problem with simulation setup.To start, I am using creo/elments Pro. The application: Glass as it fits within seal. For 3 days now I have tried to get the results of the deflection of...
View ArticleHow a material with hardness can be created in Creo/Simulte, is there any...
Hi I am involved in FE analysis of an assembly in which one of the component is made out of C45 hardened to 50 HRC, Now I struck with creating a material with hardness properties to it. I strongly...
View ArticleTrying to run Simulate in Creo 2.0: "cannot find ANSYS solver" message
Howdy PTC'ers, Long-time user here, just starting to use Creo 2.0. I'm trying to run a simple FEA case, and I keep getting an error message in the Diagnostic box: "Cannot find ANSYS solver, check...
View ArticleMold Analysis Lite
Mold Analysis Lite was integrated into Creo 3. PTC dropped Plastics Advisor after Wildfire 5, I think. I was happy to see it back because in the initial phases of a design I just want to look at fill...
View ArticleCompiled Measures Data at Each Time Step
Hello All,I am trying to find an easy way to export measures for each time step in a non-linear analysis. For instance, I have 5 time steps, and I want the measures for each time step, so they can be...
View ArticleCreo3: Stress doesn't change regardless of load.
Hi, I'm trying to run a Creo 3.0 simulation of load on a disk. When I run the simulation, the stress remains constant regardless if my load is 100 psi or 0 psi. I've attached two images of the part....
View ArticleCreo Simulate 3.0: Cyclical Stress Analysis?
A project I'm working on will have a 1/16" thick, 25"x25" stainless steel sheet that will be mounted to hinges along two parallel edges. The middle will be supported by a bar attached to a linear...
View ArticleLinkage Synthesis Using Gometric Constraint Programming
Feb 6 2015 Hello. I am a mechanical inventor, and have recently become interested in parametric CAD due to two articles, both by E. C. Kinzel, J.P Schmiedeler, and G. R. Pennock, titled Kinematic...
View ArticleClik here to view.
How do I measure the torque output of a gear in Mechanisms?
Hi First off I have used gear connection as opposed to a cam follower. I have my output angular velocity but I also need the output Torque and I don't know how to analyse this? Thanks for the help,...
View ArticleClik here to view.
Rigid Body Analysis - 3D Bolt Pattern
Does anybody have a 3D bolt pattern analysis already programed in Excel? This is a spreadsheet where the reaction loads are calculated at all the points. I have included a screenshot for...
View Article