Clik here to view.
Dynamic analysis
Hi all,in the dynamic analysis we have (Creo 2):- time analysis- shock analysis- frequencies analysis- random analysisI need always a modal analysis before; but I have the problem that I can't use...
View ArticleClik here to view.
Thin plate + contact
Hi all,I use Creo 2.I would analyze this assembly where we have two identical parts composed by a thin plate with 8 holes (for bolts that are simulated as fasteners) and a thin tube that is weld on the...
View ArticleThermal analysis with interference fit
Hi,I have a shaft that is pressfit into a stack of thin plates. I want to determine the point in time that the interference fit between the plates and shaft will be at a minimum if I heat the outer...
View ArticleClik here to view.
Non-linear material properties in Creo Simulate?
Hello, I have been using Creo Simulate 2.0 for a few months for linear static structural analysis of plastic parts.Now I want to move on to non-linear analysis.I am facing difficulties in understanding...
View ArticleClik here to view.
Get Maximum and Minimum values for results?
Hello,It is sometimes difficult to locate the region where there is a maximum/minimum value for a result.Aditionally it is difficult to understand which is the maximum/minimum value for a result.Is...
View ArticleClik here to view.
shear&moment diagram
hiwhen i draw shear and moment diagram i have diagram not like diagram i studyand not like numberanyone can explain this graphi have same shear diagram but moment diagram not start form zeroI don't...
View ArticleSimulate adhesion between rubber and plastic?
Hello, I have received a task of simulating a difficult scenario.Rubber (Elastollan 1185A) is over moulded over a plastic part (PBT GF20).The rubber stays on the part due to adhesion between the...
View ArticleNon-linear analysis with contacts and multiple load sets
I am running a static non-linear analysis with a contact interface and 3 load sets. The setup for the analysis does not give me the choice of summing the load sets, and the results do not give me the...
View ArticleClik here to view.
Change Overlay Unreformed Edge Color
Is this possible? I'd like to set the color to black (purple is the default) and I looked for a config option to do so, but I had no luck finding one.
View ArticleDoes MathCAD Express support region tags? Does Creo 3 support Analysis?
When I create an Analysis from the Analysis tab in Creo Parametric (no "Behavioral Modeler"), the only "type" option available is Prime Analysis. From the Prime Analysis dialogue, I can initiate or...
View ArticlePiece weight permanently displayed.
hello,In this simulation, we see the weight of the piecepermanently displayedat eachchange operationroom. How comethis operation.Kind regards. Denis. http://www.youtube.com/watch?v=PzwHB6R1iho
View ArticleFix displacement in only +ve direction for non-linear analysis?
Hello, I am performing non-linear static analysis and have the following 2 questions: 1. I want to constrain a surface such that it is not allowed to move in the +Z direction but free to move in the -Z...
View ArticleHow export Creo Simulation results in word format?
How export Creo Simulation results in word format?
View ArticleClik here to view.
problem with buckling / snap through (FR : flambement / cloquage)
Hi ! I have a plate, clamped between two walls; the plate is curved on the left and I impose a déplacement to the right side, so the plate will come to an unstable position and then will move to the...
View ArticleChange of materials
I am using different kinds of materials when making simulations on a beam. I use steel as my datum material. Then I fill in the following data in the material properties dialog box. Material 1 -...
View Articlehow do weighted links work?
I'm trying to understand how weighted links work and could use some help. I should mention that I am attempting to use a weighted link to distribute a reaction force to a surface. I create a weighted...
View ArticleHow to calculate bearing load
Hi All, I have a bearing assembly with me in creo. but I am not able to get satisfactory result in Simulate, There is somethign wrong while applying bearing load.Can anyone help me in resolving this...
View ArticleClik here to view.
User need help with Simulation setup.
Hi all,I have a problem with simulation setup.To start, I am using creo/elments Pro. The application: Glass as it fits within seal. For 3 days now I have tried to get the results of the deflection of...
View ArticleEurocode 3 anyone?
I have an assignment where I need to analyze a structure and have it approved according to the Eurocode 3 standard. It is a rather simple steel frame that serves two functions. It is used for...
View ArticleClik here to view.
Color of the mesh elements
Hi all,when in the mesh there are more of one type of element (generally tetra) we have a different color of the elements: a different kind of blue.in creo 2 we have the possibility of generate a more...
View Article