Pro/E, ANSYS & Windchill all rolled into one... (help)
Have an engineer that is using Windchill to manage his design files. He's got ANSYS connected to Creo Elements Pro. When he sends the file to ANSYS it puts two pipes " | | " in front of the name and...
View ArticleHow do I display true displacement in the results
Can someone tell me how to display true displacement in the results window? I'm trying to analyze a snap. I want to see how it fits as it moves through its motion.I only see the scale setting. If I set...
View ArticleDisappearing contacts
Hello, We have a moderately large model with many contacts. The contacts are required to get the correct force system into some of the components. Simpler component models just don't get close to a...
View ArticleClik here to view.
how to apply bearing constraint?
how to apply bearing constarints at the end of the shaft as shown in the image below?
View ArticleMeshing of two parts
Hi, Is there any way to copy a mesh from a part or assembly to other?I see inconsistancy in mesh with parts if I refine it. Is it possible to view results of Pro/Mechanica in Lite version? --Dhinesh
View ArticleQueries on modelling hydrostatic force acting on tank
I have a rectangular atmospheric tank (open at the top) that is supported on 4 legs that are fully constrained. The tank is about 1 meter high and is able to hold 20 bbls of water.The atmospheric tank...
View ArticleMechanica memory allocation vs actual usage
We've established here that setting Mechanica's memory allocation to around half your available memory is still a pretty good guideline, even though that's more likely to mean 6 GB than the 128 MB...
View ArticleStress analyze
I need to do a stress analyze of a hook feature in a plastic material in SI units.But I don't have the material properties file for my material: Sabic Cycoloy C2100HF.I do have a full datasheet for the...
View ArticleMapkeys in simulate, how?
Afternoon, In WF4 it was - Tools - mapkeys - and didn't matter if in Pro/e of Mechanica. I can use mapkeys in Creo Parametric. I can customise the ribbon quick access tool bar in Parametric. I can...
View ArticleClik here to view.
Mass properties are not calculated
Just starting on Creo 2.0, and when I save a part (or assembly) I get the following conflict window pop up: "Mass properties are not calculated" Now.... I know what it means The trouble is I have not...
View ArticleThin wall enclosure subjected to external pressure
Hello,I simulates a small thin walled cylinder, closed at both ends.It is subjected to external pressure.To have no constraints, I am Loading inertial balance.I run the simulation, I travel and the...
View ArticleMessage that the disk is full and the calculation stops in Simulate
Hello,Tobegin:Windows 7pro32 bit.Mydisk spaceis 1.33TB1.63TB ofI am an administrator, I have all the rights andI have nothinglimited.Concernscreosimulatetwo Example:I'm in adirectory definedfora pieceI...
View ArticleClik here to view.
A bouncing ball simulation
I was scanning the social net a few days ago, and came across this discussion in another community: I am trying to create a dynamic simulation of a bouncing ball as part of my advanced CAD class. I am...
View Articlenew blog post: Singularities and Isolate for Exclusion AutGEM Controls
I added a new post, called "Singularities and Isolate for Exclusion AutoGEM Controls", to my blog.
View ArticleClik here to view.
How to Properly Constraint Exoskeleton Thigh
Hello Creo Analysis Expert I am doing a group project to develop and exoskeleton suit I attempt to analyse the stress of key on the hub area but it the value came up awefully large as I don't know...
View ArticleSpam!!!!!!!!!
Hi PTC admin and others here,,, Downloaded lots of rubbish notifications from the [Analysis and Simulation] community to my email inbox this morning Anyone receiving massive amounts of spam inviting...
View ArticleMore disappering contacts
Hi, Another 'straight forward' model. only 12 contacts part accuracies are resonably close to each other (certainly, adjacent offending parts are) The last time I encountered this type of problem, the...
View ArticleClik here to view.
MathQuest - is there an equation for this?
I have a sketch that I have no way to describe mathematically but I find myself recreating it many times in a project. It is in a sense logarithmic but not really. The idea is that I have one known...
View ArticleScrew Ball movement in Creo 2.0
Hello all,I was wondering how to define a screw ball mechanism in CREO 2.0.Will be glad to get some help on this.Thanks in advance,Yuri
View ArticleHow can you define thermal conductivity as a function of a coordinate system?
I want to model thermal conductivity varying in the x direction with respect to a function that I input.
View Article